एपेक्स सीपी4 स्मार्ट वार्मर

विनिर्देश

• Tempreature Accuracy: +/- 0.5°C
• Tempreature Range: 20°C – 45°C (86°F – 113°F)
• पावर: 10W
• आकार: 47सेमी x 16सेमी x 7सेमी
• Weight: 0.450kg without power bank

Washable Sanitary sleeve

1. A) Fold the bottom end and position it beneath the inner support strap. Fasten the bottom end using the snap button.
   B) Fold the top ends of the opening and fasten the sleeve using the snap buttons. Snap fasteners are easily released when pulled from an angle.
   
2. Before using the APEX SmartWarmer™, it’s essential to always verify the battery level.
   
3. USB-A प्लग को पावर बैंक से कनेक्ट करें
   Place the Power bank inside the SmartWarmer´s pocket
   
4. चालू करने के लिए पावर बटन दबाएँ।
   • A If you plug the USB-A plug into the power bank without turing the ON button, after around 1minute the power bank will go into hibernation mode.
     In this case you will have to unplug plug the USB-A into the power bank. Remeber to always turn the ON button once you have pluged the power bank.
     
   • B) Boot display ACE Factory default temperature is set at 36°C
   • C) Press the button to select the temperature. Wait for 2 seconds for the program to save the desired  temperature.
     सहेजे जाने पर श्रव्य ध्वनि सचेत करेगी।
     तापमान स्थिर होने के लिए 5 मिनट तक प्रतीक्षा करें।

Setting the temperature between 20°C – 30°C.
Make sure the APEX SmartWarmer™ is at a lower ambient temperature.
If stored or used in higher ambient temperature the display will indicate HI and the system will stop heating.

टिप्पणी:
The APEX SmartWarmer™ is not a cooling device.

अद्वितीय ट्रिकेल हीटिंग सिस्टम
चमकता डिस्प्ले यह संकेत देता है कि हीटर चालू है।ट्रैक रखें – टाइमर मोड:

• A) Press the timer button –
  CP4 will be shown on the display. There are 4 pre-installed countdown timers: 5min/10min/15min and 20min.
• B) Select the timer you wish to use and press the timer button to save.
• C) Press once again the timer button to activate, ON will appear on the display and audible sound will alert.
  While the timer is on, the display will show the temperature.
• D) 5 seconds audible sound will alert once the timer has reached the countdown.
• Press the timer button to repeat the action.
• शेष मिनटों को याद करने के लिए टाइमर बटन दबाएँ।

Deactivate timer mode.

• Press the timer button for 3 seconds and select CP4, press CP4.

Turning the APEX SmartWarmer™ OFF

• Press the power button for 3 seconds – OFF will appear on the display.
• The last set temperature will be saved. Gently unplug the USB-A plug from the the power bank.

Power Bank´s – minimum requirements

1. 5V | +2A – Orange/Red color USB-A output (QC3.0/QC4.0)
2. USB-A output must deliver above 2A (ampएरे)
3. 18.5डब्ल्यूएच
4. USB-A output – QC 3.0 or PD 18.5Wh
5. 8,000mAh (मिलीamperes hour) 18.5Wh
   Test performance using the mentioned above

Power Bank: 10°C ambient temperature | Temperature set at 36°C = 8hrs.

Choosing the correct Power Bank:

• Use Smart Power / Charging USB-A Ports with  QC3.0 | QC4.0 or Power Delivery 18.5Wh. Orange/Red or blue USB-A outputs ports have a smart powering/charging capability.
• These colored ports are equipped with intelligent  circuitry that can detect the APEX SmartWarmer´s  power requirements and adjust the voltage  automatically.

टिप्पणी:

• The APEX SmartWarmer™ is designed to maintain loaded ET and AI guns at a constant and reliable temperature avoiding COLD SHOCK.
• Preheating ET/AI guns and sheaths is also highly recommended before loading the straw/s.
• APEX SmartWarmer™ is not designed for transporting fresh embryos.
• Transport Fresh Embryos at YOUR OWN RISK

The 3 latches and adjustable strap enables you to carry ro redluohs ruoy revo rehtie snoitarugnoc suoirav around your waist.

उरुग्वे में निर्मित

दस्तावेज़ / संसाधन

एपेक्स सीपी4 स्मार्ट वार्मर [पीडीएफ] उपयोगकर्ता पुस्तिका APEX, CP4, CP4 स्मार्ट वार्मर, CP4, स्मार्ट वार्मर, वार्मर

संदर्भ

• उपयोगकर्ता पुस्तिका